Wood is a sensitive material that needs a lot of care when handling for it to function well. The moisture condition it is stored should be of about 2-4 percent and a good temperature range of 60-80 degrees. The heat should be on and working prior to placing the flooring. All these should go in line with what the manufacturer has stated about the material. The installer you hire to do the work should not violate any of the rules so as to achieve better results. The following points will help you know about Hardwood Flooring Salt Lake City.
Maintain the ideal temperatures and humidity for the hardwood. Many customers are dissatisfied with poorly maintained wood which is spoilt by unfavorable climate. When the material is improperly maintained it swells in the summer and shrinks or gapping during the winter. To avoid this, you can have a pot of hot water kept on the stove to help regulate the temperatures.
Ensure you read the instructions that have been set by the manufacturer on spacing and adhere to them. The spacing set by the manufactured should be adhered to, ensure the person installing also adhered to the instructions. The spacing is very essential when the wood expands and by creating spaces that allow for these expansions the floor will not bend particularly during the summer.
These expansion gaps should be maintained between rooms. Where a room meets another room, there should be expansion joints. There is a design commonly known as T molding that can guide you to achieve this. The moisture can be regulated using a meter that will help you note when the humidity is too low or when it is high. If the moisture content is above twelve percent, you should wait till it dries before you lay it down.
A glued down floor is likely to wear out in some years. Therefore, you should either click it together or glue it together or but do not glue it down to the sub-floor unless there is a special reason. When the floor is stapled down, it is likely to lead to squeaks and creeks that are hard to handle. Ensure you check the instructions from the manufacturer on how to go about it.
To get a good job all together, check the way the nailing is being done to avoid problems in future. The nailer being used should be of good quality and the gauge, nail length and spacing between nails should be well done. Ensure the PSI settings are good.
Some of the materials may be of poor quality and may remain unused due to these defects as they may in future create problems. There is always a likelihood that five to ten percent of the materials you buy will go to waste. Ensure that you put this into consideration when buying and buy extra material to avoid being disappointed.
Finally, you need to use scratch resistant surfaces such as an aluminum oxide that does not show much scratching though the wood still dents under pressure. With the above information, you achieve the best flooring that will be well maintained.
Maintain the ideal temperatures and humidity for the hardwood. Many customers are dissatisfied with poorly maintained wood which is spoilt by unfavorable climate. When the material is improperly maintained it swells in the summer and shrinks or gapping during the winter. To avoid this, you can have a pot of hot water kept on the stove to help regulate the temperatures.
Ensure you read the instructions that have been set by the manufacturer on spacing and adhere to them. The spacing set by the manufactured should be adhered to, ensure the person installing also adhered to the instructions. The spacing is very essential when the wood expands and by creating spaces that allow for these expansions the floor will not bend particularly during the summer.
These expansion gaps should be maintained between rooms. Where a room meets another room, there should be expansion joints. There is a design commonly known as T molding that can guide you to achieve this. The moisture can be regulated using a meter that will help you note when the humidity is too low or when it is high. If the moisture content is above twelve percent, you should wait till it dries before you lay it down.
A glued down floor is likely to wear out in some years. Therefore, you should either click it together or glue it together or but do not glue it down to the sub-floor unless there is a special reason. When the floor is stapled down, it is likely to lead to squeaks and creeks that are hard to handle. Ensure you check the instructions from the manufacturer on how to go about it.
To get a good job all together, check the way the nailing is being done to avoid problems in future. The nailer being used should be of good quality and the gauge, nail length and spacing between nails should be well done. Ensure the PSI settings are good.
Some of the materials may be of poor quality and may remain unused due to these defects as they may in future create problems. There is always a likelihood that five to ten percent of the materials you buy will go to waste. Ensure that you put this into consideration when buying and buy extra material to avoid being disappointed.
Finally, you need to use scratch resistant surfaces such as an aluminum oxide that does not show much scratching though the wood still dents under pressure. With the above information, you achieve the best flooring that will be well maintained.
About the Author:
If you are looking for information about hardwood flooring Salt Lake City locals can pay a visit to our web pages online here today. Additional details are available at http://www.kuantumllc.com now.
No comments:
Post a Comment