Hot tub owners in Portland OR have over the years been encouraged to remove or sell their spa baths that are not functioning properly. The process of unwanted hot tub removal is less complicated than the installation process. However, it is critical that you plan well prior to any removal efforts. The work involved is more or less half that of installation process.
You should assess the state in which your tub is in so that you decide whether to replace or repair it. It is because most removals have discovered catastrophic matters of maintenance and fixing. People in the cool areas are the most affected because they fail to winterize the tubs leading to water freezing in the pipes. Hence, it is important to first get to know the condition of the bath so that you judge which remedy action to take.
Rereading the manual is useful when it comes to removing your unwanted tub. This will juggle up your memory on the original construction of the plunge bath. You are supposed to have a full idea of how the electric wires are connected, how the heater was hooked up and so on. By doing so, you will not only ensure a successful removal but you will also be putting your own safety first.
A good number of people own whirlpools that are connected electrically and some may be of high voltage. Electrical needs should be greatly considered before disconnecting any wires. The standard bath should have a central disconnection box to allow you to isolate power. If you will not be replacing your plunge bath, then seal the box so that it will be easy to make future connections during another installation.
The next thing in the regimen should be the actual removal of tub. Here, carefully cut the electricity flow by unplugging the electrical wires including the gas supply. You should not compromise your safety when dealing with electricity because you can be easily be electrocuted when exposed to live wires. Cutting the electrical flow will make you avert shocks while cutting the wires.
You should then disassemble the spa skirt. Some manufacturers in Portland OR produce these goods with some components connected using screws. These can be easily removed manually using a screw driver. On the other hand, some may be built using wooden slats that are connected through tongue and groove which makes it relatively easy to disassemble the skirt without having to cut any individual components.
Cutting the actual hot tub is probably the most difficult part of the removal process. This is so because most of them are made of materials that are hard enough to last for long. It can be plastic or any other durable material. To cut it into smaller pieces, you will need the right gear and a jigsaw. A reciprocating saw will make you cutting work easy.
Cutting the Jacuzzi into smaller pieces makes their carriage from the house to the yard easy. It is important that you properly dispose them in a dumpster to keep the environmental effect at the low. It is significant you put on gloves and goggles so that you avoid causing injuries to your hand and keeping dust away from your eyes respectively.
You should assess the state in which your tub is in so that you decide whether to replace or repair it. It is because most removals have discovered catastrophic matters of maintenance and fixing. People in the cool areas are the most affected because they fail to winterize the tubs leading to water freezing in the pipes. Hence, it is important to first get to know the condition of the bath so that you judge which remedy action to take.
Rereading the manual is useful when it comes to removing your unwanted tub. This will juggle up your memory on the original construction of the plunge bath. You are supposed to have a full idea of how the electric wires are connected, how the heater was hooked up and so on. By doing so, you will not only ensure a successful removal but you will also be putting your own safety first.
A good number of people own whirlpools that are connected electrically and some may be of high voltage. Electrical needs should be greatly considered before disconnecting any wires. The standard bath should have a central disconnection box to allow you to isolate power. If you will not be replacing your plunge bath, then seal the box so that it will be easy to make future connections during another installation.
The next thing in the regimen should be the actual removal of tub. Here, carefully cut the electricity flow by unplugging the electrical wires including the gas supply. You should not compromise your safety when dealing with electricity because you can be easily be electrocuted when exposed to live wires. Cutting the electrical flow will make you avert shocks while cutting the wires.
You should then disassemble the spa skirt. Some manufacturers in Portland OR produce these goods with some components connected using screws. These can be easily removed manually using a screw driver. On the other hand, some may be built using wooden slats that are connected through tongue and groove which makes it relatively easy to disassemble the skirt without having to cut any individual components.
Cutting the actual hot tub is probably the most difficult part of the removal process. This is so because most of them are made of materials that are hard enough to last for long. It can be plastic or any other durable material. To cut it into smaller pieces, you will need the right gear and a jigsaw. A reciprocating saw will make you cutting work easy.
Cutting the Jacuzzi into smaller pieces makes their carriage from the house to the yard easy. It is important that you properly dispose them in a dumpster to keep the environmental effect at the low. It is significant you put on gloves and goggles so that you avoid causing injuries to your hand and keeping dust away from your eyes respectively.
About the Author:
If you are in need of information about unwanted hot tub removal, go to the web pages online here today. Additional details are available at http://www.nwspecialtymoving.com now.
No comments:
Post a Comment